Cables for Audio & Video at Home

Furutech HF-A-NCF HDMI Active Optical Cable (AOC) uses fibre optic technology to transport the digital HDMI signal, enabling lossless signal transfer over far greater distances than is possible with standard copper HDMI cables, and reducing the risk of EMI and RFI interference. NCF Strain Relief（Multi-material Hybrid Construction） The HF-A-NCF’s cable clamp incorporates Furutech’s proprietary electrical and mechanical damping material, NCF (Nano Crystal2 Formula). NCF features a special crystalline material with two 'active' properties. First, it generates negative ions that eliminate static. Second, it converts thermal energy into far infrared. Furutech combines this material with nano-sized ceramic particles and carbon powder for their additional 'piezoelectric effect' damping properties. Electrical and mechanical vibration and static derived noise are eliminated, which increases picture and sound resolution, delivers blacker backgrounds and boosts colour vividness. Noise Resistant The HDMI-HF-A-NCF features the latest in optical transmission technology with its connectors incorporating special photoelectric conversion chips to deliver ultimate balanced signal amplification. Even over distances that are susceptible to noise and signal degradation, the HDMI-HF-A-NCF will deliver stable and near lossless 8K signal transmission (Power not required – Plug ’n Play). Optical fiber The HF-A-NCF features OM3 “optical multi-mode” optical fiber, which has higher transmission speed and bandwidth than OM1 and OM2. It also has a bending diameter of OM3 is 20mm, making it easier to use in environments where fiber installation is difficult or in complex piping. This extreme quality HF-A-NCF AOC cable (Optic Fiber and α- Conductor Hybrid Cable) is produced in a micro-precision ISO 7 (Class 10,000) dust-free factory. Features Supported Bandwidth: Superior 48Gbps (GB/sec) bandwidth delivering ULTRA HIGH-SPEED HDMI™ CABLE 8K/60p Supported signal specifications: 8K/60p/48Gbps , 4K/120p/32.08Gbps , HDCP1.4/2.2/2.3, eARC/ARC, HDR10/HDR10+ , VRR/60Hz~240Hz(Refresh rate) , DSC, QMS, QFT, ALLM. Aluminum alloy connector with thick gold-plated contacts: Zinc and aluminum alloy metal connector covers - textured to reduce the influence of vibration. HDMI A connector parts treated with Furutech’s α(Alpha)-Process (2-Step Alpha Cryogenic and Demagnetizing Process) to deliver stable, optimized signal transmission. Thick layer of gold plating on contacts with minimal magnetism offer reliable and stable transmission with extreme performance. Double Layer Aluminum Foil Shields prevent Static and EMI. Exceeding stipulated specifications for Crosstalk and Noise, the HDMI-HF-A-NCF features double aluminum foil shielding for each twisted conductor. Featuring tension resistant Kevlar Synthetic Fiber to withstand external stresses. Antiresonance Sheath: passing UL/CL3 flame resistance testing and RoHS compliant, the very flexible PVC used in the HDMI-HF-A-NCF will reduce effects of electrical and mechanical resonance on signal transmission. The HDMI-HF-A-NCF cable has been purposely limited to a diameter of 4.7mm to produce an extremely light and flexible cable that delivers the highest possible performance.

Furutech’s Pure Transmission FI-UK 1363 NCF Piezo Ceramic series connector bodies feature several breakthrough construction techniques. The body of the connectors incorporates an “active” damping material: Nano Crystal² Formula (NCF). Incorporated into selected Furutech products, NCF features a special crystalline material that has two 'active' properties. First, it generates negative ions that eliminate static. Second, it converts thermal energy into far infrared. Furutech combines this remarkable material with nano-sized ceramic particles and carbon powder for their additional 'piezoelectric effect' damping properties. The resulting Nano Crystal² Formula is the ultimate electrical and mechanical damping material. Created by Furutech, it is found exclusively in Furutech products. Nano Crystal² Formula eliminates static, “interconverts” thermal, mechanical and electrical energy and damps vibrations—all for the finest Furutech Pure Transmission signal imaginable. Specifications Rhodium-plated α (Alpha) Hybrid copper Conductor Body Material: Polycarbonate incorporating Furutech’s “NCF” anti-resonance nano-sized crystalline, piezo ceramic particles and carbon damping material Housing Material: Fireproof ABS body/housing (RoHS compliant) Specifications: Accommodates cable diameters of 6.0mm to 20.0mm Dimensions: Body 48mm (W) x 50.2mm (L) x 55.8mm (H)

The Furutech FT-SWS-D NCF Box is a dual power distributor with high-end Schuko connectors. Its high quality design allows it to provide a non-degraded AC electrical signal that greatly contributes to the audio quality of your system. An engineering piece of art. The finest high end performance schuko wall socket available . The contacts of these sockets are made of pure copper with rhodium plating, ensuring excellent signal conductivity. Moreover, these contacts are treated with Alpha (α), a cryogenic process that eliminates impurities to the maximum and promotes conductivity. The front panel of the mains distributor has a beautiful carbon and fiberglass coating. Nano Crystal² Formula (NCF) Incorporated into selected Furutech products, NCF features a special crystalline material that has two 'active' properties. First, it generates negative ions that eliminate static. Second, it converts thermal energy into far infrared. Furutech combines this remarkable material with nano-sized ceramic particles and carbon powder for their additional 'piezoelectric effect' damping properties. The resulting Nano Crystal² Formula is the ultimate electrical and mechanical damping material. Created by Furutech, it is found exclusively in Furutech products. Features High-purity Alpha OCC wire (14AWG / 2.0 Sq.mm ) star wired. Beautifully engineered high-end performance rhodium-plated nonmagnetic pure copper FT-SWS-NCF(R) schuko socket IEC inlet: FI-06 NCF. Schuko socket body constructed with RoHS compliant audio grade nylon/fiberglass incorporating a special anti-resonance nano-sized crystalline “NCF” material and piezo ceramic carbon damping material. Polycarbonate cover incorporates special anti-resonance nano-sized crystalline material “NCF” for improved vibration damping. Results in greater resolution, clarity, powerful dynamics, and an ultra-quiet soundstage in which music develops more fully without artificial upper-frequency “presence region” glare. Dimensions: 164.0mm (L) x 108.5mm (W) x 71.0mm (H) approx, without spikes. All metallic parts are treated by *FURUTECHα(Alpha) Process (Super Cryogenic & Demagnetize Treatment.) Made in Japan Specifications α (Alpha) Pure copper main conductor (t：0.5mm) Insulation Materials: Nylon/fiberglass with special “NCF” anti-resonance damping material - nano-sized crystalline, piezo ceramic particles and carbon powder Bracket with a 1.0mm thick Zinc/steel brace plate Beautifully-crafted Carbon fiber finished Aluminum face plate (color coated). Specified for wire diameters of 2.8mm or 5.5 Sq.mm/10AWG Max. (set screw) Dimensions: 152.0mm (L) x 81.0mm (W) x 48.0mm(H) Furutech’s total attention to detail and build quality extends right down to a specially designed patent-pending pressure plate that increases the contact area of the Alpha Conductors.

Furutech Pure Transmission Philosophy. Meticulous build quality is a large part of the engineering equation. Furutech Pure Transmission technology turns a macro lens on every element of power and signal transfer applying optimized engineering solutions to well-known problems such as contact resistance, EMI and RFI rejection, grounding, and using the best materials and processes available. The Furutech Floating Field Damper System The Floating Field Damper completely solves the biggest problem you never realized you had by star grounding the metal parts in which floating magnetic fields are created by current flow through the connector. A precisely engineered, sprung metal bridge ties the various parts together and shunts the potential to ground, significantly reducing distortion for ultra clean and stable power transfer. The Critics Speak “Furutech's reputation in the audio connector sector is rock solid as it is for their apparently science-driven approach to even unconventional solutions like CD and LP demagnetizers … The [Piezo Powerflux AC cord] is possibly the most radical implementation of hi-tech materials anyone in this sector has attempted yet … Based on its noise killer damping action, I'd expect good results in systems which need greater organization, control and noise floor skills. Though far from cheap, Furutech's construction, ingredients and fit 'n' finish are top shelf. That makes certain rather more expensive offerings look like crazy home-brew or unduly funky efforts.”-- Srajan Ebaen, 6moons.com Specifications α(Alpha) pure-copper rhodium-plated conductors Floating Field Damper System* eliminates magnetic interference Nylon/fiberglass body incorporating carbon particles that absorb vibration and resonance Specified for cable diameters from 6mm to 17.5mm Dimensions: Body length 40.2mm × 39.6mm diameter x 72mm overall length Metal cable clamp improves grip and reduces mechanically and electrically induced distortion Rating: 15A/125V

Furutech's FI-15ME is a high end connector that is made from nylon/fiberglass, main body and outer cover and uses non-plated α (Alpha) Pure copper Conductor. Furutech is known the world over for a huge variety of top-quality OEM parts and delivers consistently superior results by following Pure Transmission principles; examine every link in the power and signal path and ultimately optimize each and every element. Specifications Non-plated α (Alpha) Pure copper Conductor Floating Field Damper System* prevents induced magnetic fields Nylon /fiberglass main body and outer cover. Specified for cable diameters of 6.6mm to 13.0mm (Wire size of 3.5mm2 (12AWG) max.) Stainless cover fixed screws Connection: Set screw Dimensions: 31.0mm X 33.3mm X 72.0mm overall length Made in Japan

Furutech Pure Transmission Philosophy: Meticulous build quality is a large part of the engineering equation. Furutech Pure Transmission technology turns a macro lens on every element of power and signal transfer applying optimized engineering solutions to well-known problems such as contact resistance, EMI and RFI rejection, grounding, and using the best materials and processes available. The Floating Field Damper completely solves the biggest problem you never realized you had by star grounding the metal parts in which floating magnetic fields are created by current flow through the connector. A precisely engineered, sprung metal bridge ties the various parts together and shunts the potential to ground, significantly reducing distortion for ultra clean and stable power transfer. “Furutech's reputation in the audio connector sector is rock solid as it is for their apparently science-driven approach to even unconventional solutions like CD and LP demagnetizers … The [Piezo Powerflux AC cord] is possibly the most radical implementation of hi-tech materials anyone in this sector has attempted yet … Based on its noise killer damping action, I'd expect good results in systems which need greater organization, control and noise floor skills. Though far from cheap, Furutech's construction, ingredients and fit 'n' finish are top shelf. That makes certain rather more expensive offerings look like crazy home-brew or unduly funky efforts.” -- Srajan Ebaen, 6moons.com Specification 24k Gold-plated conductors α (Alpha) pure-copper (Gold) α (Alpha) pure-copper rhodium-plated conductors (Rhodium) Floating Field Damper System* eliminates magnetic interference Nylon/fiberglass body incorporating carbon particles that absorb vibration and resonance Specified for cable diameters from 6mm to 17.5mm Dimensions: Body length 40.2mm × 39.6mm diameter x 76.2mm overall length Metal cable clamp improves grip and reduces mechanically and electrically induced distortion Rating: 15A/125V 10A/250V Made in Japan

All enthusiasts look for the same qualities from their systems: Verisimilitude to the original event, a sense of engagement promoting suspension of disbelief, a visceral immersion in the audio and video experience. To engage without effort requires meticulous preparation of the entire playback chain, especially signal-carrying cables, and especially the power cord which carries the same signal your system plays back. Picking up a Furutech power cord, from these supple, beautifully-made upgrade power cords for Home Theater, CD, DVD, Blu-ray, Projectors and Flat Screen Panels, the integrity of the cable’s build is immediately apparent. Furutech Pure Transmission quality turns a macro lens on every element of power transfer applying optimized engineering solutions to well-known problems such as contact resistance, EMI and RFI rejection, and using the best materials and processes available. The Odeon Power Cord delivers blacker blacks and more vivid colors and gives sound greater resolution, clarity, and dynamics in an ultra-quiet soundstage where the sound blooms seamlessly from top to bottom without artificial upper-frequency “presence region” glare. The new slimline IEC connector also allows for easy connection to space restricted IEC sockets that can be found on some high-end projectors and HD screens. Features Fitted with a Non-plated Furutech FI-15ME(Cu) AC connector (The Odeon-E with FI-E11Cu) and a FI-C15(Cu) IEC connector RoHS-compliant audio grade flexible PVC sheath improves vibration isolation Special audio grade polyethylene Insulation contributes to reduced capacitance Floating Field Damper™ US Patent No.: 6,669,491/ European Patent (EP1445837) For FI-15ME(Cu) version only. Made in Japan Specifications Conductors: 37-strand Silver plated-OFC 0.26mm x 2 cores / 37-strand α-OFC 0.26mm x 1 core Insulation: Audio grade Polyethylene (Red, Yellow, Green) OD: 3.5mm diameter approx. Inner Filler: Cotton Barrier Layer: Paper Tape Wrap Sheath: RoHS-compliant Audio grade flexible PVC (Dark Red), 10.0mm diameter approx. Outer Sleeve: Nylon yarn braid (Black), 10.8mm diameter approx. Length: 180cm approx.

If you’re a musician or a recording professional, ask yourself the following question: Do your current power cords make sense? They might make sense to your budget or in the context of your recording and playback equipment, but are they making sense to your brain? Does the music you create in the studio sound like the music in your head, natural and inviting and emotional? Or do you listen to your music with an imaginary clipboard in your lap, checking off what’s right about the sound you’re getting—and what isn’t so right? The new Furutech Astoria and Empire power cords were designed for demanding professionals just like you. Developed in Tokyo with extensive feedback from musicians and recording professionals, the Astoria and Empire power cords have been specifically tuned and balanced to deliver greater punch and dynamics to your sound—more of what you’re hearing in your head and in your heart. In fact, choosing between the Astoria and the Empire provides you with even greater control over the type of sound you’re trying to achieve. Pick the Astoria if you’re aiming for quick response and natural speed, mated with deep and powerful bass. The Empire, on the other hand, offers a well-balanced sound with incredible resolution so that you hear every detail and nuance. It’s up to you. Just replace the existing power cords for your amplifiers, mixing consoles, microphone preamps and even your entire recording and playback system, and you’ll immediately hear more top-to-bottom coherence in the sound. Dynamic range will be greater than ever before, and the music will sound effortless and expansive instead of congested, edgy or muddy. Your music will start to make more sense where it counts—in your brain. The legendary design team at Furutech are experts when it comes to preserving the signal path and delivering an end result that’s accurate, honest and uncompromised. Our innovative (Alpha) PC-Triple C power cable, used in both the Astoria and the Empire, is the result of a proprietary forging process that involved repeated rounds of metal folding—the same method used to create the katana, the sword used by Samurai warriors! We’ve taken that art of sword-making to new levels, however, by applying variable high pressures to high-purity oxygen-free copper. This creates a forging process that is identical to folding the steel of a katana tens of thousands of times. This ensures that the crystal grain boundaries deep inside the copper are rearranged so that electrical current travels through the signal path more smoothly than ever before. Add our renowned gold-plated connectors, our noise-reducing (Alpha) conductor shielding, our vibration-controlling RoHS-compliant flexible PVC sheath and our patented Floating Field Damper grounding system and you’ll have a razor-sharp tool for extracting the finest results-- both in the studio and on the stage. Use Furutech’s Astoria and Empire power cords for all your recording and playback needs and the end result will not be subtle. Features Fitted with Gold-plated Furutech FI-11M (G) or FI-E11(G) and FI-11(G) IEC connector α (Alpha) conductor shield for protection against radiated noise RoHS-compliant Audio grade flexible PVC sheath improves vibration isolation Special Audio grade flexible PVC Insulation contributes to reduced capacitance Floating Field Damper™ (Earth/Ground Jumper System) with US Patent No.: 6,669,491/ European Patent (EP1445837) Made in Japan Specifications Conductors: 45-strand PC Triple C 0.32mm x 3 cores Insulation: Audio grade Flexible PVC (Brown, Light Blue, Green with Yellow striping) OD: 5.0mm diameter approx. Inner Sheath: Audio grade Flexible PVC (Black) Shielding: 0.12mm OFC Wire Braid Sheath: RoHS-compliant Audio grade flexible PVC (Dark Green), 16.0mm diameter approx. Outer Sleeve: Nylon yarn braid Length: 150cm approx.

If you’re a musician or a recording professional, ask yourself the following question: Do your current power cords make sense? They might make sense to your budget or in the context of your recording and playback equipment, but are they making sense to your brain? Does the music you create in the studio sound like the music in your head, natural and inviting and emotional? Or do you listen to your music with an imaginary clipboard in your lap, checking off what’s right about the sound you’re getting—and what isn’t so right? The new Furutech Astoria and Empire power cords were designed for demanding professionals just like you. Developed in Tokyo with extensive feedback from musicians and recording professionals, the Astoria and Empire power cords have been specifically tuned and balanced to deliver greater punch and dynamics to your sound—more of what you’re hearing in your head and in your heart. In fact, choosing between the Astoria and the Empire provides you with even greater control over the type of sound you’re trying to achieve. Pick the Astoria if you’re aiming for quick response and natural speed, mated with deep and powerful bass. The Empire, on the other hand, offers a well-balanced sound with incredible resolution so that you hear every detail and nuance. It’s up to you. Just replace the existing power cords for your amplifiers, mixing consoles, microphone preamps and even your entire recording and playback system, and you’ll immediately hear more top-to-bottom coherence in the sound. Dynamic range will be greater than ever before, and the music will sound effortless and expansive instead of congested, edgy or muddy. Your music will start to make more sense where it counts—in your brain. The legendary design team at Furutech are experts when it comes to preserving the signal path and delivering an end result that’s accurate, honest and uncompromised. Our innovative (Alpha) PC-Triple C power cable, used in both the Astoria and the Empire, is the result of a proprietary forging process that involved repeated rounds of metal folding—the same method used to create the katana, the sword used by Samurai warriors! We’ve taken that art of sword-making to new levels, however, by applying variable high pressures to high-purity oxygen-free copper. This creates a forging process that is identical to folding the steel of a katana tens of thousands of times. This ensures that the crystal grain boundaries deep inside the copper are rearranged so that electrical current travels through the signal path more smoothly than ever before. Add our renowned gold-plated connectors, our noise-reducing (Alpha) conductor shielding, our vibration-controlling RoHS-compliant flexible PVC sheath and our patented Floating Field Damper grounding system and you’ll have a razor-sharp tool for extracting the finest results-- both in the studio and on the stage. Use Furutech’s Astoria and Empire power cords for all your recording and playback needs and the end result will not be subtle. Features Fitted with Non-plated Furutech FI-11M(Cu) or FI-E11(Cu) and FI-11(Cu) IEC connectors α (Alpha) conductor shield for protection against radiated noise RoHS-compliant Audio grade flexible PVC sheath improves vibration isolation Special Audio grade flexible PVC Insulation contributes to reduced capacitance Floating Field Damper™ US Patent No.: 6,669,491/ European Patent (EP1445837) Made in Japan Specifications Conductors: 80-strand PC Triple C 0.18mm x 3 cores Insulation: Audio grade Flexible PVC (Brown, Light Blue, Green with Yellow striping) OD: 3.5mm diameter approx. Inner Sheath: Audio grade Flexible PVC (Black) Shielding: 0.12mm OFC Wire Braid Sheath: RoHS-compliant Audio grade flexible PVC (Dark Green), 12.8mm diameter approx. Outer Sleeve: Nylon yarn braid Length: 150cm approx.

High Performance 75 ohm coaxial cable. Double screen made of aluminum foil and braided silver plated copper. A guide made of pure silver subjected to the Furutech Alpha process. α(Alpha)-Pure Silver conductor is Pure Silver conductor wire strands treated with the α(Alpha) process. Features Pure Silver Conductor + Fluoropolymer α (Alpha)-Pure Silver Conductor(7/0.18mm) 25 AWG α (Alpha)-Pure Siver Conductor(0.18 sq.mm) Transmission Delay Time：3.80 ± 0.10 ns/m Made in Japan Specifications Construction: α (Alpha)-Pure Silver Conductor(7pcs/0.18mm) (25 AWG) / (0.178 sq.mm) Insulation-1 : Fluoropolymer Insulation-2 : Polyethylene foam Shield: PET/Al Tape + 0.10mm α (Alpha)Conductor wire Braid Sheath: Flexible PVC ( Green) Characteristic Impedance :75 ± 3 Ω Overall Diameter: 8.0mm (25AWG) Note: Price Per Meter, Without Termination

Don't miss out on any of the stunning visual excitement of 4K and 8K video. Thrill to every last incredible detail of movies, concerts, gaming, multi-channel music, and more with Pangea Audio Premier SE MKII. It's the high-speed HDMI cable of choice for the latest hi-res Blu-ray players, streamers, cable boxes, gaming consoles, and other AV sources. Premier SE MKII supports the HDMI 2.1a standard, which is the most recent update of the HDMI specification. It supports a wide range of higher video resolutions and refresh rates including 8K60 and 4K120, and resolutions up to 10K. Dynamic HDR formats are also supported, and bandwidth capability is increased up to 48Gbps. And, of course, it is backward compatible with your legacy HDMI video sources. Excellent Audiophile Performance Pangea Audio's Premier SE MKII is a 24awg HDMI cable featuring the highest purity 6% silver-plated Cardas Grade One Copper for the vital signal conductors. In addition to its excellence for video applications, this design makes the cable a must-have for audiophiles transmitting high resolution audio files over HDMI, delivering the absolute best sound possible from high-end home theater processors. Premium Materials and Meticulous Manufacturing HDMI cable performance varies wildly due to two factors: the raw materials and how they are employed. It's one thing to use fine materials. However, if they are not manufactured correctly, the resulting cables will not be of uniform impedance and will betray signal loss even in short lengths. Premier SE MKII starts with the finest available copper – the incredible Cardas Grade One Copper – and insulates it with premium Nitrogen-Injected Polyethylene Multi-Layer Foam. This special insulation is crucial because it provides significantly lower signal loss than lesser materials. Pangea HDMI cables are manufactured using state-of-the-art Swiss-made production equipment that is rarely used in commercial products. The accuracy of this Swiss equipment ensures that all the signal pairs within the cable are exactly the same length - even with the twisting necessary - so that all signals arrive simultaneously at the connector. All testing of Pangea HDMI cables is done by Time Domain Reflectometry instruments to ensure cables do not suffer from timing errors regardless of cable length. Affordable Excellence in Hi-End HDMI Cable Performance Pangea's Premier SE MKII cable makes premium performance highly affordable. It uses superior materials and an approach based on substantial research, development, and expert insights, providing benefits that you can see hear and see. Premier SE MKII was designed by Jay Victor, one of the biggest behind-the-scenes product designers in the audiophile world and a longstanding expert on cable technology. Jay designed Pangea Audio Premier HDMI cables using high-quality 24awg conductors to keep the cable as flexible as possible for installation friendliness without compromising performance in any way. Premium Silver-Coated Cardas Grade One Copper Signal Conductor Pangea Premier SE MKII cable uses no-compromise Cardas Grade One Copper, which George Cardas of Cardas Audio developed for his own premium cables. George’s copper is mined in Arizona, then shipped to a New England factory where it is very slowly drawn into conductors in a process that includes reduction annealing between steps to further purify and meld the copper into what George calls "the most amazing audio conductor I have ever experienced. It is quite simply the best copper on the planet." Jay has the Cardas Grade One Copper wire shipped to a second factory, where the wire is plated with a 6% pure silver coating. "I have found silver plating is crucial to digital cable performance," reports Jay, "and I use it in all my digital audio designs." Premier SE MKII meets HDMI 2.1a certification and is certified for "High Speed" applications. The tough nylon braided jacket is both strong and flexible. Specifications High-Speed HDMI cable supports 4K and 8K video up to 48Gbps Highest purity 6% Silver-plated Cardas Grade One Copper conductors 24 awg conductors Premium Nitrogen-Injected Polyethylene Multi-Layer Foam dielectric Certified HDMI 2.1a Tough nylon braided jacket Manufactured using state-of-the-art Swiss-made production equipment All testing of Pangea HDMI cables is done by Time Domain Reflectometry instruments to ensure cables do not suffer from timing errors regardless of cable length

The Ethernet Cable Designed for Audiophile Applications. If you are using a wired network connection for music or video streaming, or if your Ethernet connection is otherwise critical to your AV system, don't rely on the stock Ethernet cable that came with your gear. Step up to the superior materials and workmanship of Pangea Audio's Premier Ethernet Cable, designed by audio legend Jay Victor for excellent all-around performance. Silver Coated Conductors Unlike off-the-shelf Ethernet cables, Pangea's Premier Ethernet Cable boasts 26 AWG copper conductors coated with silver. "I have found silver plating is crucial to digital cable performance," reports Jay Victor, "and I use it in all my digital audio designs." Premier Ethernet Cable also goes the extra step by using low loss PE insulation. In addition to the individual shielding of each signal pair, as required by Cat 7 specs, Premier is triple shielded for maximum resistance to EMI and RFI. When performance is important, choose the Ethernet cable that's specially designed for audiophile applications. Treat your system to Premier. Specifications 26 AWG Silver Plated Copper Conductors Low Loss PE Insulation Individual Shielding on Each Signal Pair (required by Cat 7 Spec.) Meets or Exceeds Currently Published Bandwidth Specs for Cat 7 & Cat 8 Triple Shielded for Maximum Resistance to EMI & RFI

Bring out the best low bass performance from your subwoofer with Pangea Audio Premier subwoofer interconnect cable. Designed by industry legend Jay Victor, Pangea Audio’s Premier audio interconnects offer best-in-class performance at anything near the price – and way beyond! Premier features technological innovations and the very best materials, including US-made Cardas Grade One Copper, which many in the industry consider to be the finest copper available. This copper costs 20% more than the famous Japanese-made PCOCC copper that most experts formerly rated as the world’s finest copper. Insulating the Cardas Copper is an advanced PE insulation. PE is one of the best commercially available insulators and was chosen because it has a smooth, relaxed sound. Covering the cable is an advanced nylon braid that bends easily yet protects the cable from cracking and scuffing. . Triple Shielded Design To reject noise and interference from inside the cable and the outside room, Pangea Premier interconnects are triple-shielded. Each conductor has its own shield and then the entire cable is encased in separate foil and braided shields. Advanced Conductor Design The cheapest and most common design generally found in signal cables uses a single conductor for each channel, with the return being the shield only. Most cable manufacturers use this design in their entry-level cables. A second, more advanced design uses a signal conductor and a separate return conductor for each channel, which is separate from the shield. Most high-end audio cable manufacturers use this second design in their entry-level cables. Pangea Audio Premier interconnect features a far more advanced design. Premier cables feature a separate solid core Cardas Grade One Copper conductor for the right and left channels and then a separate OFC copper conductor for each channel’s return conductor. Conductors for each channel are then wrapped in a foil shield to reduce inter-channel distortion and the entire cable is shielded with two additional layers of shielding. This design is more expensive and complex to produce but is sonically superior to the cheaper methods. "Quite Simply the Best Copper on the Planet" This Pangea Audio cable uses no-compromise Cardas Grade One Copper, which George Cardas of Cardas Audio developed for his own premium cables. George’s copper is mined in Arizona, then shipped to a New England factory where it is very S-L-O-W-L-Y drawn into conductors in a process that includes reduction annealing between steps to further purify and meld the copper into what George calls "the most amazing audio conductor I have ever experienced. It is quite simply the best copper on the planet." "The bottom line is that the best phono cartridges manufactured in the world, the best transformer winders, and the best cable manufactures in the world are converting to this smooth sounding Cardas Grade One Copper," George reports. "It is simply stunning how using a combination of space-age technology (reduction annealing) and ancient drawing process (diamond dies and a slow multi stage annealing) can result in such a refined product," says George. Beautifully Made, Prime 400 Premium RCAs The crowning touch of Pangea Audio Premier interconnects is the beautifully made Prime 400 RCA termination. These premium RCAs feature a highly advanced form of copolymer core insulator wrapped with gold-plated brass connections. The gold-plated one-piece solid center pin is split, which gives it a compression grip at the connection point. The Prime 400 RCA ground is also gold-plated with four cuts, so it securely grips the female RCA ground. Extremely Durable Baked-on Chromium Finish Covering the RCA is a machined brass barrel with a baked-on chromium finish. We asked the designer, Jay Victor, why he chose this finish. "I’ve designed and built over one hundred RCA cables for various brands around the world and found that after months or years of use, the paint will eventually flake off the barrel. This chrome finish is extremely durable and will last for years without cracking or flaking," answered Jay. "And besides, it looks sexy, doesn’t it?" We agree. Why the low price? Working closely with the designer, Jay Victor, and directly with four different manufacturers in the US and Asia, Pangea Audio is able to offer the Premier audio interconnects at a price far below its competition. Specifications Conductors use US-Made Cardas Grade One copper Separate solid core Cardas Grade One Copper conductor for the right and left channels Separate OFC copper conductor returns Flexible PE insulation Conductors for each channel are wrapped in a foil shield Entire cable is shielded with two additional layers of shielding Advanced nylon outer braid resists cracking Premium black chrome plated Prime 400 RCAs Gold-plated one-piece solid center pin Split center pin for a compression fit Machined brass barrel Extremely durable baked-on chromium finish RCA-to-RCA termination

The trouble with most audio cables on the market is that they have just two conductors – a single solid core center conductor that carries the positive charge and a braided outer wire that carries both the ground signal and act as a shield against RF (Radio Frequency) and EM (Electro-Magnetic) noise. You can see immediately a problem with this design. Mixing RF and EM noise with the ground signal wire pollutes the audio signal. Many high-end audio cable manufacturers have avoided this problem by having two independent wire conductors – one for the positive and another for the negative – and surrounding these with a separate outer RFI and EMI shield. Balanced – XLR audio cables were originally designed for the professional music industry where long cable runs are the norm. They feature three internal conductors plus an outer shield. One conductor carries the positive signal, another the negative signal and the third that grounds to the two circuits on either end together. This design provides superior RFI and EMI shielding and promotes greater signal integrity between electronic components. Noticing that an increasing number of high-end audio manufacturers were featuring balanced connectors on their gear, audio design guru, Jay Victor, set out to create an affordable balanced cable that was superior to anything in its price class. "Watch out for cheaply made XLR-terminated audio cables," warns Jay. "Some manufacturers 'cheat' by using only two conductors in their cable and then using the cable's braided shield for both circuit grounding and shielding. This is not a true 'balanced' cable." "I refused to take any short-cuts in the Pangea Audio True Balanced Audio Interconnects design. I included three independently-insulated conductors plus a two-layer outer shield," Jay explained. "For the signal conductor I chose Cardas Grade One Copper. The other conductors, which are not as critical are the high grade OFC copper. Each conductor is wrapped in my favorite smooth-sounding PE insulation." "Quite Simply the Best Copper on the Planet" This Pangea Audio cable uses no-compromise Cardas Grade One Copper, which George Cardas of Cardas Audio developed for his own premium cables. George’s copper is mined in Arizona, then shipped to a New England factory where it is very S-L-O-W-L-Y drawn into conductors in a process that includes reduction annealing between steps to further purify and meld the copper into what George calls "the most amazing audio conductor I have ever experienced. It is quite simply the best copper on the planet." "The bottom line is that the best phono cartridges manufactured in the world, the best transformer winders, and the best cable manufactures in the world are converting to this smooth sounding Cardas Grade One Copper," George reports. "It is simply stunning how using a combination of space-age technology (reduction annealing) and ancient drawing process (diamond dies and a slow multi stage annealing) can result in such a refined product," says George. Another Technical Achievement: Pangea Audio XLR 500 Connectors "The most impressive external feature are the XLR connectors," observes Jay. "It took me months of searching to find these beauties. I rejected dozens of prototypes. For a time I was worried I wouldn't be able to find connectors that were technically superior and not cost a fortune. Finally, one of my sources sent me a set that knocked me out. They feature gold-plated solid pins, machined metal covers, PE insulators, and a high-quality locking mechanism. I had them plated in black chrome because it resists chipping and scratching and, besides, I just love that finish." Once the cables were finished, Jay sent them to Pangea with a note. It said: "I'm sure you'll love these. They are the best affordable balanced cables I've ever designed. They sound fantastic!" Who Should Use Balanced Cables? Introducing the Pangea Audio True Balanced Audio Interconnects. If your electronics offer balanced connections, these are the cables you should be using for lower background noise and cleaner sound . Specifications Conductors use US-Made Cardas Grade One copper Separate solid core Cardas Grade One Copper conductor for the right and left channels Separate OFC copper conductor returns Flexible PE cable insulation Conductors for each channel are wrapped in a foil shield Entire cable is shielded with two additional layers of shielding Advanced nylon outer braid cover resists cracking Premium black chrome plated Prime 500 XLRs Gold-plated one-piece solid connector pins Spring-type locking XLR mechanism Extremely durable baked-on chromium finish Hand-soldered XLR-to-XLR cable termination Supplied as a pair

Designed by industry legend Jay Victor, Pangea Audio’s Premier audio interconnects offer best-in-class performance at anything near the price – and way beyond! Premier features technological innovations and the very best materials, including US-made Cardas Grade One Copper, which many in the industry consider to be the finest copper available. This copper costs 20% more than the famous Japanese-made PCOCC copper that most experts formerly rated as the world’s finest copper. Insulating the Cardas Copper is an advanced PE insulation. PE is one of the best commercially available insulators and was chosen because it has a smooth, relaxed sound. Covering the cable is an advanced nylon braid that bends easily yet protects the cable from cracking and scuffing. Triple Shielded Design To reject noise and interference from inside the cable and the outside room, Pangea Premier interconnects are triple-shielded. Each conductor has its own shield and then the entire cable is encased in separate foil and braided shields. Advanced Conductor Design The cheapest and most common design generally found in signal cables uses a single conductor for each channel, with the return being the shield only. Most cable manufacturers use this design in their entry-level cables. A second, more advanced design uses a signal conductor and a separate return conductor for each channel, which is separate from the shield. Most high-end audio cable manufacturers use this second design in their entry-level cables. Pangea Audio Premier interconnect features a far more advanced design. Premier cables feature a separate solid core Cardas Grade One Copper conductor for the right and left channels and then a separate OFC copper conductor for each channel’s return conductor. Conductors for each channel are then wrapped in a foil shield to reduce inter-channel distortion and the entire cable is shielded with two additional layers of shielding. This design is more expensive and complex to produce but is sonically superior to the cheaper methods. "Quite Simply the Best Copper on the Planet" This Pangea Audio cable uses no-compromise Cardas Grade One Copper, which George Cardas of Cardas Audio developed for his own premium cables. George’s copper is mined in Arizona, then shipped to a New England factory where it is very S-L-O-W-L-Y drawn into conductors in a process that includes reduction annealing between steps to further purify and meld the copper into what George calls "the most amazing audio conductor I have ever experienced. It is quite simply the best copper on the planet." "The bottom line is that the best phono cartridges manufactured in the world, the best transformer winders, and the best cable manufactures in the world are converting to this smooth sounding Cardas Grade One Copper," George reports. "It is simply stunning how using a combination of space-age technology (reduction annealing) and ancient drawing process (diamond dies and a slow multi stage annealing) can result in such a refined product," says George. Beautifully Made, Prime 400 Premium RCAs The crowning touch of Pangea Audio Premier interconnects is the beautifully made Prime 400 RCA termination. These premium RCAs feature a highly advanced form of co-polymer core insulator wrapped with gold-plated brass connections. The gold-plated one-piece solid center pin is split, which gives it a compression grip at the connection point. The Prime 400 RCA ground is also gold-plated with four cuts, so it securely grips the female RCA ground. Extremely Durable Baked-on Chromium Finish Covering the RCA is a machined brass barrel with a baked-on chromium finish. We asked the designer, Jay Victor, why he chose this finish. "I’ve designed and built over one hundred RCA cables for various brands around the world and found that after months or years of use, the paint will eventually flake off the barrel. This chrome finish is extremely durable and will last for years without cracking or flaking," answered Jay. "And besides, it looks sexy, doesn’t it?" We agree. Why the low price? Working closely with the designer, Jay Victor, and directly with four different manufacturers in the US and Asia, Pangea Audio is able to offer the Premier audio interconnects at a price far below its competition. One listen and you’ll agree – this is an outstanding cable that could sell for much, much more. Specifications Conductors use US-Made Cardas Grade One copper Separate solid core Cardas Grade One Copper conductor for the right and left channels Separate OFC copper conductor returns Flexible PE insulation Conductors for each channel are wrapped in a foil shield Entire cable is shielded with two additional layers of shielding Advanced nylon outer braid resists cracking Premium black chrome plated Prime 400 RCAs with Teflon insulation Gold-plated one-piece solid center pin Split center pin for a compression fit Machined brass barrel Extremely durable baked-on chromium finish RCA-to-RCA termination RCA O.D. (measured at the widest point) 13.2mm

Jay Victor's new Pangea Audio Prime Interconnect closely follows a principle attributed to the legendary physicist, Albert Einstein. Einstein was quoted as saying that one of his guiding principles was "everything should be made as simple as possible, but not simpler." Jay's new Prime cable is a simple design, but it's executed brilliantly with carefully chosen premium materials. The Prime conductors are 99.99% pure oxygen-free copper. Most cables at this price point use cheap tinned copper or, even worse, made with a cheaper metal. To reduce RF and EM interference, the conductors are twisted and then covered with a double-sided AL/Mylar shield. Conductors are insulated with advanced foamed PE insulation. This foamed PE is a step up from ordinary solid PE because it is filled with tiny air bubbles to reduce dielectric absorption. The entire cable is then covered with a highly flexible yet very tough woven fabric cover. Low Price, Big Performance To keep the price low, Prime features non-magnetic and non-ferrous RCA covers with an expensive-looking metallic finish. The RCAs and stereo mini-jacks feature gold-plated machined brass conductors with a Polyoxymethylene (POM) insulator. The RCA center pin is split to provide a better connection for the positive conductor. Pangea Audio Prime Interconnect comes in your choice of RCA-to-RCA or RCA-to-Mini connectors. The RCA ends can be connected to female RCAs up to five inches apart. Specifications 99.99% pure oxygen-free copper Conductors Double-sided AL/Mylar shield Advanced foamed PE insulation Non-magnetic and non-ferrous RCA covers RCAs feature gold-plated machined brass conductors with a Polyoxymethylene (POM) insulator RCA center pin is split to provide a better connection RCA O.D. (measured at the widest point) 13.2mm

Two years in the making, Pangea Audio's Premier SE ground-breaking turntable cable – or, more accurately, turntable cable with superior grounding – has finally arrived. This amazing RCA-to-RCA cable was definitely worth the wait! What distinguishes the Premier SE from lesser turntable cables? For that we need a little background. For nearly fifty years, all turntables came with a dedicated cable running straight from the tonearm base to the phono stage. In the last ten years, however, more and more popular selling turntables – such as the Pro-Ject Debut Carbon, for example – have been designed with RCA outputs on the back of the turntable. This welcome design change allows users to choose whichever audio interconnect cable they wanted, but the benefits come with a big problem. For best sound, there should be a separate ground wire running from the turntable back to the preamp. But 99.99% of the quality audio cables on the market lack this necessary grounding wire. Several companies introduced interconnects with a separate ground wire, but these grounding cables were not integrated into the cable. Instead, they were fixed outside of the cable, resulting in a less than ideal grounding solution. Grounds for a Superior Ground Pangea Audio tasked veteran cable designer Jay Victor with creating a special cable that incorporated the turntable grounding wire into the interconnect cable’s shield layer. Jay accepted the challenge, but he soon discovered why no manufacturer had accomplished this before. It proved extremely difficult to incorporate the grounding wire into the cable and still have access to it on both ends. After a year of trial and error, Jay’s team finally produced a prototype that seemed to meet all of Jay’s strict requirements. Jay sent out a group of samples to a close-knit group of audiophiles around the world. Everyone loved the sound of the prototypes – except for one individual who detected a faint hum when the cable was placed in close proximity to a group of inexpensive wall-wart power supplies powering his system. It turns out there were more than five noisy power supplies in total, so this was an unusual situation. But, no matter. Jay went back to the drawing board to eliminate the hum. Unique Twin-Lead Design It took another year and several more prototypes. Eventually, Jay was not only able to silence the hum, but he also made a cable that to all the tester’s ears sounded even better than the previous version. The Pangea Audio Premier SE Turntable Cable is a unique twin-lead audio cable with integrated ground and wire management. Premier SE features the highest purity Cardas Grade One Copper and OFC conductors. The unique configuration of conductors features multi-gauge conductors with PE dielectric and dual-layered shielding for both right and left channels, delivering exceptionally low noise performance with any high-end audio turntable. Based on the advanced engineering specifications and product development timeline, the Premier SE Phono Cable should be priced much higher at $200. Due to Pangea Audio’s volume purchasing power and aggressive pricing strategy, we are pleased to bring this cable to you for less than $100. Needless to say, you won't find a better turntable cable at anywhere near the price – or even by spending way, way more. Specifications RCA-to-RCA turntable cable Delivers exceptionally low noise performance with any high-end audio turntable Unique twin-lead design Separate L-R cables plus integrated ground cable Wire management blocks hold all three cables Cardas Grade One Copper conductors Polymer-coated OFC Copper conductors Multi-Gauge, using three different conductor gauges Separate aluminum foil and braided OFC Copper shields Color-coded PE dielectric for each cable array Black/gray nylon-covered TPR jacket Premium gold-plated RCAs

An Entry-Level Audiophile USB Cable That Sounds Like a Million Bucks... Pangea Audio's Premier USB may have an entry-level price, but the performance is anything but. It sounds like a million bucks. Premier is an audiophile USB cable that offers a significant upgrade from stock USB cables. If you love streaming music, you'll love the benefits of switching to Pangea Premier USB. Premier USB's features include precision-wound 23-gauge signal conductors using oxygen-free copper plated with 1.25% pure silver. It also boasts a separately shielded 20 AWG tinned copper power conductor, an advanced form of PE polyethylene insulation, and a tough woven nylon braided jacket. We occasionally get questions about USB cables from customers who are getting into digital audio streaming. They wonder why it would be worth investing in an audiophile-grade USB cable when they've been told that all USB cables are created equal as far as digital signals are concerned – that a $5 cable conveys the "zeros and ones" of a digital stream just as well as a more expensive cable. For the definitive answer, we asked Pangea Audio cable design expert, Jay Victor, "How can one digital USB cable sound better than another?" "A USB cable is not just carrying a bunch of zeros and ones," explained Jay. "The cable carries an electrical signal from one circuit to another. Lots of things can interfere with this signal, like radio frequency interference (RFI) and electromagnetic interference (EMI). Anything that affects that signal will cause distortion. Some of these distortions are bound to be audible." This made sense to us. We've heard differences between the various USB cables we sell. Some of our customers swear by USB cables costing $1,000 and more. So USB cable quality definitely matters. However, the cost of a high-quality cable doesn't have to break the bank. Especially when the cable is made by Pangea Audio. "How Can We Make Our USB Cables Better?" After three years of making and selling the popular Pangea Audio USB-PC and USB-AG cables, Pangea Audio challenged Jay. How could he make these cables even better? "I can think of two things right away. We can increase the gauge of the signal conductors and use a more advanced type of insulation," answered Jay. "But give me a little time and I'll think of some more things to improve." A few weeks later, Jay followed up. "I came up with three designs…. This entry-level USB cable is an audiophile design all the way. For Pangea Premier USB, I've taken the basics of the design of the mid-level cable, Premier SE, including the advanced PE insulation and triple shielding. But in order to keep the price tag low and the performance level high, I use a high grade 23-gauge oxygen-free copper plated with 1.25% pure silver for the conductors. This cable will kick ass if sold for anything less than $50." We invite you to try Pangea Audio's Premier USB cable for yourself. You'll discover it to be a huge upgrade from standard USB cables and far superior to any other USB cable in its price range and beyond. Specifications Description: USB A to B, molded connectors with gold plating Tough woven nylon braided jacket (black/blue) Signal Conductors: 23 AWG 1.25% Silver-plated oxygen-free copper Signal Conductor Insulation: Advanced form of PE polyethylene Power Conductors: 20 AWG tinned copper Shielding: Triple Shielded. Signal shielded from power, and overall double shield

Two years in the making, Pangea Audio's Premier SE Fiber Optic Digital Audio Cable is vastly superior to typical off-the-shelf fiber optic cables. Premier SE uses a premium Multi-Core Plastic Optical Fiber (POF). It also boasts superior termination for best optical transparency. The end result is a high-performance optical cable that's ideal for audiophile applications, because of its significantly better sound quality. The vast majority of fiber optic cables on the market use a single Multi-Mode Plastic Optical Fiber (POF) rather than a group of smaller optical fibers. This single-core optical fiber is used by cable manufacturers for reasons of economy. But if you are looking for a no-compromise optical cable, it isn't an ideal solution. Here's why. The single Multi-Mode Plastic Optical Fiber is composed of a cylindrical "core" surrounded by a "clad" layer. Due to its large core, some of the light rays that make up the digital pulse may travel a direct route, whereas others zigzag as they bounce off the cladding. These alternate paths cause the different groups of light rays, referred to as modes, to arrive separately at the receiving point. "The pulse, an aggregate of different modes, begins to spread out, losing its well-defined shape. The need to leave spacing between pulses to prevent overlapping limits the amount of information that can be sent," notes legendary cable designer Jay Victor. "This is the primary drawback of single-core POF cables, and I believe the various modes and conversion processes can cause jitter." The Multi-Core Solution for Best Sound To overcome the scattering effect (modes) of the light waves in a single-core POF cable, a multi-core POF is the solution. The Pangea Premier SE optical cable utilizes this technology to produce a superior grade optical cable. The difference is that instead of a single optical fiber, a group of smaller optical fibers are used. "In listening to both single POF, and multi-core POF cables, I have always found that the multi-core cables sound significantly better," notes Jay Victor. "There is definitely less transmission loss, but I believe there is also a minimization of timing errors, and a faster, more accurate detection of light pulses, which can ultimately reduce jitter." Superior Termination for Optimal Optical Transparency Another critical factor in optical cable performance is how the fiber is terminated. Most optical cables are "hot plate terminated", which is exactly what it sounds like. The end is simply pressed up against a hot steel plate to hopefully create a flat surface. However, this is not really the best way to ensure an optically transparent termination, which is desirable for obvious reasons. A better termination, results in less loss. For this reason, the Pangea Premier SE optical cable has a polished termination, which is far superior in optical transparency, results in less loss, and is seldom used in any single POF cables because of cost. Essentially, the termination is polished mechanically, using a very fine grit abrasive material to end up with a very fine, optically transparent end. This is an expensive method, but, if the best performance is desired, this is the method to use. Specifications Premium optical digital cable for audio applications Designed by industry legend Jay Victor Type: Multi-Core Plastic Optical Fiber, 19 Core Attenuation: <.136 dB/meter Termination: Polished

Designed by Jay Victor, the entry-level Pangea Premier optical cable uses a single Multi-Mode Plastic Optical Fiber (POF), and this is what most optical cables on the market use. However, there are many quality levels available from the various fiber manufacturers, so how do you know what you are getting? In general, you don’t. Most brands will never tell you any specifications for their fiber, so it’s difficult to make a choice or to compare choices. This promotes the idea that all-optical cables are the same, but they definitely are not. For the Pangea Premier optical cable, Jay Victor selected a very high-end Japanese fiber that has an attenuation spec. of <.16 dB/meter, "which is much lower than normal fibers (some I've tested are as much as .8 dB/m), and of course, much more expensive," says Jay. Another critical factor in optical cable performance is how the fiber is terminated. Most optical cables are “hot plate terminated”, which is exactly what it sounds like. The end is simply pressed up against a hot steel plate to hopefully create a flat surface. However, this is not really the best way to ensure an optically transparent termination, which is desirable for obvious reasons. A better termination results in less loss. For this reason, the Pangea Premier optical cable has a polished termination, which is far superior in optical transparency, results in less loss, and is seldom used in any single POF cables because of cost. Essentially, the termination is polished mechanically, using a very fine grit abrasive material to end up with a very fine, optically transparent end. This is an expensive method, but, if the best performance is desired, this is the method to use. Step-Index Multimode Fiber (Single POF) Plastic optical fiber is a step-index multimode optical fiber, composed of a cylindrical "core" surrounded by a "clad" layer. The light refraction index of the core is higher than that of the cladding. Light traveling through the core is therefore reflected at the core-clad interface, so long as the angle of its incidence with the interface is smaller than a certain "critical angle" (theta max). In this way, the light is repeatedly reflected from the interface as it progresses through the core to the end of the optical fiber. Due to its large core, some of the light rays that make up the digital pulse may travel a direct route, whereas others zigzag as they bounce off the cladding. These alternate paths cause the different groups of light rays, referred to as modes, to arrive separately at the receiving point. "The pulse, an aggregate of different modes, begins to spread out, losing its well-defined shape. The need to leave spacing between pulses to prevent overlapping limits the amount of information that can be sent," notes Jay Victor. "This is the primary drawback of Single POF cables, and I believe the various modes and conversion processes can cause jitter." Jay Victor's design for Pangea Premier optical cable takes maximum advantage of the benefits of Single POF cables, including low cost compared to multi-core cable, while minimizing any inherent drawbacks and optimizing performance. Compare it to any other entry-level optical cable for a nice upgrade. Specifications Superior quality optical digital cable Designed by industry legend Jay Victor Type: Step-Index Multimode Fiber (Single POF) Attenuation: <.16 dB/meter Termination: Polished

EVO3 Sequel power cable offers increased performance over IsoTek’s multi-award winning Premier, featuring optimised conductor strand geometry and active shielding. Sequel comes in a standard length of 2 metres. Suitable for CD players, preamps, tuners, power amps, Blu-ray players, music servers, TVs, soundbars and more! Features The conductors are in a parallel construction with slight rotational twist. This established technique remains the first line of defence against RFI and EMI rejection. Silver plated 99.9999% OFC conductors offer an exceptional level of purity with enhanced conductivity. They are less likely to fracture or degrade over time. Silver is an excellent conductor and when combined with a high purity copper provides impressive electrical properties. Teflon FEP dielectric (insulation) is chemically inert and has a very low dielectric constant over a wide frequency range. FEP possesses a very high degree of stress crack resistance and a low coefficient of friction making it an exceptional dielectric. FEP is the first choice for safety in both temperature and electrical insulation. Cotton filler has been used to give the cable internal strength and reduce microphony. Cotton also possesses excellent dielectric properties, the best of a solid material. A mylar wrap is used to secure the construction and offer a barrier shield prior to the application of a flexible PVC jacket. The addition of the mylar and cotton form a buffer with the PVC so as to maintain exceptional dielectric properties. An earthed OFC shield insures maximum RFI rejection, thus preventing Common Mode noise effecting the live and neutral conductors. PVC is used as an outer jacket to give a high degree of flexibility and mechanical strength. Sequel cable is terminated using IsoTek’s bespoke Audiophile grade moulded connectors of solid OFC with 24ct gold plated conductors. These offer the highest quality performance and are less prone to tarnish. Specifications CONDUCTOR SIZE 3 x 2.0sqmm (increased diameter conductor strands) CONDUCTOR MATERIAL Silver-plated 99.9999% Oxygen Free Copper DIELECTRIC Flourinated Ethylene Propylene (FEP) DIELECTRIC CONSTANCE 2.1 FILLER Cotton PVC BARRIER Mylar SHIELD Oxygen free copper braid (OFC) OUTER JACKET High flexibility PVC CABLE POWER RATING 16 Amp CABLE LENGTH 2.0m standard (no custom length) OUTER DIAMETER 10mm TERMINATION 24ct gold plated audiophile-grade connectors Support Brochure Awards & Reviews Misc

EVO3 Premier was inspired by discussions with high-end electronics companies, many of whom produce audio equipment that retails for tens of thousands of pounds and yet is bundled with poor quality power cords that significantly constrain performance. Premier delivers excellent performance, and also represents outstanding value-for-money. No compromise has been made in relation to the quality of parts and materials used in its construction . Suitable for CD players, preamps, tuners, power amps, Blu-ray players, music servers, TVs, soundbars and more! Features The conductors are in a parallel construction with a slight rotational twist. This established technique remains the first line of defence against RFI and EMI rejection. Silver plated 99.9999% OFC conductors offer an exceptional level of purity with enhanced conductivity. They are less likely to fracture (compared to solid core) or degrade over time. Silver is an excellent conductor and when combined with a high purity copper provides impressive electrical properties. Teflon FEP (Fluorinated Ethylene Propylene) dielectric (insulation) is chemically inert and has a very low dielectric constant over a wide frequency range. FEP possesses a very high degree of stress crack resistance and a low coefficient of friction making it an exceptional dielectric. FEP is the first choice for safety in both temperature and electrical insulation. Cotton filler has been used to give the cable internal strength and reduce microphony. Cotton also possesses excellent dielectric properties, the best of a solid material. A paper wrap is used to secure the construction prior to the application of a flexible PVC jacket. The addition of the paper and cotton form a buffer with the PVC so as to maintain exceptional dielectric properties. PVC is used as the outer jacket to give a high degree of flexibility and mechanical strength. Premier cable is terminated using IsoTek’s bespoke Audiophile grade moulded connectors of solid OFC with 24ct gold plated conductors. These offer the highest quality performance and are less prone to tarnish. Specifications CONDUCTOR SIZE 3 x 2.0sqmm CONDUCTOR MATERIAL Silver-plated 99.9999% Oxygen Free Copper DIELECTRIC Fluorinated Ethylene Propylene (FEP) DIELECTRIC CONSTANCE 2.1 FILLER Cotton PVC BARRIER Paper OUTER JACKET High flexibility PVC CABLE POWER RATING 16 Amp CABLE LENGTH 1.5m standard (no custom length) OUTER DIAMETER 10mm TERMINATION 24ct gold plated audiophile-grade connectors Support Brochure Awards & Reviews Misc

EVO3 Initium is IsoTek’s new entry level power cable designed to offer high quality performance at an extremely fair price. Initium is a must for replacing all of your free standard black plastic power leads which have been designed down to a price not up to a quality. Suitable for CD players, preamps, tuners, power amps, Blu-ray players, music servers, TVs, soundbars and more! Features The conductors are in a parallel construction with a slight rotational twist. This established technique remains the first line of defence against RFI and EMI rejection. 99.9999% OFC conductors offer an exceptional level of purity with enhanced conductivity. They are less likely to fracture or degrade over time. PE dielectric (insulation) is chemically inert and has a very low dielectric constant over a wide frequency range. PE possesses a very high degree of stress crack resistance and a low coefficient of friction making it an exceptional dielectric. PE is a good choice for safety in both temperature and electrical insulation. Cotton filler has been used to give the cable internal strength and reduce microphony. Cotton also possesses excellent dielectric properties, the best of a solid material. A paper wrap is used to secure the construction prior to the application of a flexible PVC jacket. The addition of the paper and cotton form a buffer with the PVC so as to maintain exceptional dielectric properties. PVC is used as the outer jacket to give a high degree of flexibility and mechanical strength. Initium cable is terminated using IsoTek’s bespoke Audiophile grade moulded connectors of solid OFC. These offer good performance qualities. Specifications CONDUCTOR SIZE 3 x 2.0sqmm CONDUCTOR MATERIAL99.9999% Oxygen Free Copper DIELECTRICPolyethylen (PE) DIELECTRIC CONSTANCE 2.25 FILLER Cotton PVC BARRIER Paper wrap OUTER JACKET High flexibility PVC CABLE POWER RATING 16 Amp CABLE LENGTH 1.5m standard (no custom length) OUTER DIAMETER 10mm TERMINATION Nickel plated audiophile-grade connectors Support Brochure Awards & Reviews Misc

Certified with the latest 8K Ultra High Speed HDMI 2.1a specification, the SVS SoundPath Ultra HDMI cable performs to the latest standards of new and legacy audio video products. HDMI ARC and eARC compliant. 48Gbps bandwidth supports video resolution up to 10K. Inspired engineering and premium build materials ensure vivid picture quality, breathtaking sound, and a future-facing entertainment experience . 8K Ultra High Speed Certified 2.1a Compliant HDMI Cables Engineered to meet the latest HDMI 2.1 and 2.1a specifications and 8K ultra high speed certification, the SVS SoundPath Ultra HDMI Cable delivers vivid picture quality up to 10K and stunningly bold and detailed sound. SVS SoundPath Ultra HDMI Cables are HDMI ARC and eARC compliant. 48Gbps data bandwidth capacity flawlessly renders all high resolution video standards, including 1080p, 4K, 8K and 10K. The cables also support Dynamic HDR, Dolby Vision™, Dolby Atmos®, DTS-X®, and all legacy standards. Built to withstand heavy usage with premium materials and a high-end look and feel, the cables feature advanced shielding from interference, easy gripping, and provide secure connections for all AV components. Connect the SVS SoundPath Ultra HDMI Cable with confidence to HDTVs, soundbars, Blu-Ray players, gaming consoles, AV receivers, and other components. Features Stunning video and sound quality for truly immersive experiences Up to 48 Gbps bandwidth capacity Compatible with 8K/60Hz and 4K/120Hz resolution/refresh rate combinations Compatible with resolutions up to 10K/60Hz (compressed mode) Supports 3D and Multiview Video Bandwidth Capacity: 48 Gbps Resolution & Refresh Rate: 8K/60Hz and 4K/120Hz HDMI 2.1 and 2.1a compliant HDMI ARC & eARC compatible 8K Ultra High Speed Certified Backwards compatible with all legacy HDMI standards Available in 1, 2, and 3-meter lengths Specifications Supports HDMI versions 2.1 and 2.1a Backwards compatible with all previous HDMI versions HDMI ARC/eARC (Enhanced Audio Return Channel) Compatible Supports all surround sound formats, including: Dolby Atmos, DTS:X, and Auro 3D Supports pass-through of all HDR (High Dynamic Range) formats for clearer, deeper, more vivid colors: HDR10, 10+, Dolby Vision, HLG, and any prospective HDR formats Supports advanced gaming features such as ALLM (Auto Low Latency Mode) and VRR (Variable Refresh Rate) Supports AMD® FreeSync™ on the Xbox Series X™, Xbox® Series S, Xbox One™ X, and PlayStation® 4 Pro consoles Supports SA‑CD, DVD‑Audio, DTS‑HD Master Audio™, Dolby TrueHD™, and other high definition audio standards Supports the 21:9 cinema aspect ratio Supports up to 32 audio channels and a 1536kHz audio sampling rate Supports Deep Color with up to 16‑bits per channel, including the Sony® x.v.Color™ standard Supports simultaneous delivery of dual video streams to multiple users on the same screen